濟南玻璃隔斷的分類

Classification of Jinan glass partition

1、按主要玻璃類型分：?jiǎn)螌硬ＡЦ魯?、雙層玻璃隔斷、夾膠玻璃隔斷、真空玻璃隔斷；

1. According to the main glass types: single glass partition, double glass partition, laminated glass partition and vacuum glass partition;

2、按隔斷框架材質分：鋁合金框架玻璃隔斷、不銹鋼框架玻璃隔斷、鋼結構框架玻璃隔斷、木龍骨框架玻璃隔斷、塑鋼框架玻璃隔斷、鋼鋁結構框架玻璃隔斷、鋼木材質有框玻璃隔斷、無框純玻璃隔斷；

2. Divided by partition frame material: aluminum alloy frame glass partition, stainless steel frame glass partition, steel structure frame glass partition, wood keel frame glass partition, plastic steel frame glass partition, steel aluminum structure frame glass partition, steel wood framed glass partition and frameless pure glass partition;

3、按框架材質尺寸：26mm玻璃隔斷、50mm玻璃隔斷、80mm玻璃隔斷、85mm玻璃隔斷、100mm玻璃隔斷、定制特殊規格框架等；

3. According to the frame material size: 26mm glass partition, 50mm glass partition, 80mm glass partition, 85mm glass partition, 100mm glass partition, customized special specification frame, etc;

4、按軌道形式分：固定玻璃隔斷、移動玻璃隔斷、折疊玻璃隔斷；

4. Divided by track form: fixed glass partition, mobile glass partition and folded glass partition;

5、按高度和尺寸分：高玻璃隔斷、短玻璃隔斷、屏風隔斷；

5. By height and size: high glass partition, short glass partition and screen partition;

6、按玻璃的功能和性質分：玻璃隔斷、防火玻璃隔斷、超白玻璃隔斷、防爆玻璃隔斷、藝術玻璃隔斷等。

6. According to the function and nature of glass: safety glass partition, fireproof glass partition, ultra white glass partition, explosion-proof glass partition, art glass partition, etc.

濟南玻璃隔斷安裝步驟

Installation steps of Jinan glass partition

確定玻璃隔斷的安裝位置，在上面畫出定位線，然后用鉛筆在墻上確定高度，***根據實測尺寸定制玻璃隔斷。

Determine the installation position of the glass partition, draw a positioning line on it, then use a pencil to determine the height on the wall, and finally customize the glass partition according to the measured size.

在轉角鋁片上打兩個3mm左右的孔，將沖好的轉角鋁片放入型材中，然后根據轉角鋁片的鉆孔位置，在垂直型材上繼續鉆同樣的孔，然后用螺絲固定垂直型材的角鋁部件。

Drill two 3mm holes on the corner aluminum sheet, put the punched corner aluminum sheet into the profile, then continue to drill the same holes on the vertical profile according to the drilling position of the corner aluminum sheet, and then fix the corner aluminum parts of the vertical profile with screws.

完成后在建筑結構板下做支架，安裝玻璃夾具和上框，玻璃固定在框上，***用螺絲固定玻璃和框，上下框玻璃可以固定在水平面上。，安裝玻璃隔墻。

After completion, make a support under the building structural plate, install the glass fixture and upper frame, fix the glass on the frame, and finally fix the glass and frame with screws. The upper and lower frame glass can be fixed on the horizontal plane., Install glass partition.

濟南玻璃隔斷操作流程介紹

Introduction of Jinan glass partition operation process

根據樓板設計的水平線，順著墻高到吊頂設計水平線，沿墻截?cái)嗵斓佚埞堑拇怪彼骄€(xiàn)和水平線，畫出龍骨的放坡位置線在天地龍骨的水平線上。

According to the horizontal line of the floor design, cut off the vertical and horizontal lines of the heaven and earth keel along the wall from the wall height to the ceiling design horizontal line, and draw the grading position line of the keel on the horizontal line of the heaven and earth keel.

地龍骨安裝：按設計要求固定天地龍骨。如無設計要求，可用Ф8～Ф12膨脹螺栓或3～5寸釘固定，膨脹螺栓固定點間距為600～800mm。安裝前做好防腐處理。

Ground keel installation: fix the ground keel according to the design requirements. Available if there is no design requirement Ф 8～ Ф 12 expansion bolts or 3-5-inch nails shall be used for fixation, and the spacing between the fixed points of expansion bolts shall be 600-800mm. Anti corrosion treatment shall be done before installation.

沿墻龍骨安裝：按設計要求固定側龍骨。如無設計要求，可用Ф8~Ф12膨脹螺栓或3~5寸釘及預埋木磚固定，固定點間距800~1000mm。安裝前做好防腐處理。

Installation along the wall keel: fix the side keel according to the design requirements. Available if there is no design requirement Ф 8~ Ф 12 expansion bolts or 3~5 inch nails and embedded wood bricks shall be used for fixation, and the spacing between fixed points shall be 800~1000mm. Anti corrosion treatment shall be done before installation.

根據設計要求，將主龍骨按分級線位置固定，用4寸鐵釘固定。龍骨兩端應固定不少于三個釘子。

According to the design requirements, fix the main keel according to the position of the grading line, and fix it with 4-inch iron nails. At least three nails shall be fixed at both ends of the keel.

根據設計要求，將小龍骨按分級線位置固定，用榫頭或釘子固定。

According to the design requirements, fix the small keel according to the position of the grading line, and fix it with mortise or nail.

根據設計要求，按玻璃規格安裝在小龍骨上。如果用珠子安裝，先把珠子固定在玻璃的一側，在玻璃下面墊一塊橡膠墊，再用珠子固定玻璃；如果玻璃直接用玻璃膠固定，則應先將玻璃安裝在小龍骨的預留槽內。，然后用玻璃膠密封。

According to the design requirements, it is installed on the small keel according to the glass specification. If beads are used for installation, first fix the beads on one side of the glass, pad a rubber pad under the glass, and then fix the glass with beads; If the glass is directly fixed with glass glue, the glass shall be installed in the reserved slot of the small keel first., Then seal with glass glue.

將紙膠帶粘在玻璃四周邊緣，并按設計要求在玻璃與小龍骨之間均勻打上各種玻璃膠。待玻璃膠完全干透后，撕掉紙膠帶。

Stick the paper tape around the edges of the glass, and evenly apply various glass adhesives between the glass and the dragon bone according to the design requirements. After the glass adhesive is completely dry, remove the paper tape.

根據設計要求，用直釘或玻璃膠將各種規格、材質的珠條固定在小龍骨上。可根據需要選擇10×12mm木珠、10×10mm鋁珠或10×20mm不銹鋼珠。

According to the design requirements, beads of various specifications and materials shall be fixed on the small keel with straight nails or glass glue. 10 can be selected as required × 12mm wood bead, 10 × 10mm aluminum bead or 10 × 20mm stainless steel beads.

以上就是今天為大家分享的關于問題的相關內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://www.t3d5.cn。

The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.t3d5.cn 。